Top 9 Arduino Stepper Motor Driver – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. TIMESETL

#ad

TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects

#ad
TIMESETL #ad - This l298n board comes ready to go. Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Easy to use no assembly required.

High quality main driver chip l298n, afterflow diode protection, strong driving ability, low calorific value, strong anti-interference, more stable and reliable for Arduino projects. High efficient double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient. Just wire up motors and power, easy to use. Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
BrandTIMESETL #ad
ManufacturerTIMESETL #ad
Height1.18 Inches
Length5.91 Inches
Width3.15 Inches
Part NumberTXJ-061-US
ModelL298N motor controller

2. Gikfun

#ad

Gikfun EasyDriver Shield Stepper Motor Driver V44 A3967 for Arduino Pack of 3pcs EK1204

#ad
Gikfun #ad - Compatible with 4, 6, and 8 wire stepper motors of any voltage. The higher the voltage, the higher the torque at high speeds. Power supply range from 7v to 30V. A3967 microstepping driver.
BrandGikfun #ad
ManufacturerEsooho #ad
Height0.3 Inches
Length5 Inches
Weight0.02 Pounds
Width3 Inches
Part Numberunknown

3. Longruner

#ad

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE no Wire

#ad
Longruner #ad - Cable length: about 20cm /8-inch. 5pcs stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi. Stepping angle: 5. 625 x 1/64. Reduction ratio: 1/6. Drive module Board Size:1. 26 inchsX1. 38inchs. Motor diameter: 1. 1 inches. Wire length:9. 05 inchs. Good after-sales service. A, b, c, d four-phase led indicates the status of the stepper motor work. Stepper motor with a standard interface. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board.
BrandLongruner #ad
ManufacturerLongruner #ad
Part NumberLK67
ModelLK67
Warranty1 year warranty

4. Adafruit

#ad

Adafruit Motor/Stepper/Servo Shield for Arduino v2.3 Kit

#ad
Adafruit #ad - You'll still need to do a little soldering to put on the shield-headers or stacking headers but it should be even easier and faster to get started! This also makes it drop-in compatible with any Arduino, such as the Uno, Due, we have a fully-dedicated PWM driver chip onboard.

Only two pins sda & scl are required to drive the multiple motors, Leonardo and Mega R3. As of 3/21/2014 we are shipping motor shields with the terminal blocks, and power jumper pre-soldered on. This chip handles all the motor and speed controls over I2C. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well. New version 2. 3! completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that many steppers? I have no idea but if you come up with something send us a photo because that would be a pretty glorious project.

Instead of using a latch and the arduino's pwm pins, and since it's i2c you can also connect any other i2c devices or shields to the same pins. Instead of a l293d darlington driver, we now have the tb6612 mosfet driver: with 1. 2a per channel and 3A peak current capability.
BrandAdafruit #ad
ManufacturerAdafruit #ad
Weight0.04 Pounds
Part Number1438
Model1438

5. Organizer

#ad

Organizer CNC Shield Expansion Board V3.0 + Board + A4988 Stepper Motor Driver with Heatsink for Arduino Kits K75 3D Printer

#ad
Organizer #ad - 5. Cnc shield expansion board v3. 0 + board + a4988 stepper motor Driver with Heatsink for Arduino Kits K75. 4. Package contents: 1 x cnc shield board 1 x Board for Arduino 4 x A4988 Stepper Motor Driver.

2. Mcu: usb interface: 16u2 operating voltage: 5v digital i/o pins: 14 including 6 with pwm capability analog input pins: 6 i-i/o pin output current: 40mA max 3. 3v output current: 150mA max Flash memory: 32 kB 05kb used by bootloader - included static ram SRAM: 2 kB EEPROM: 1 kB Clock speed: 16MHz. 3. 4988 stepper motor driver board is a breakout board for Allegro's A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection;.

1. Latest for arduino cnc shield version 3. 0 grbl 09 compatible 4-axis support x, z, y, a-can duplicate x, y, z or do a full 4th axis with custom firmware using pins D12 and D13 2 x End stops for each axis 6 in total Coolant enable Compatible with A4988 or DRV8825 stepper driver Runs on 12-36V DC.
BrandOrganizer #ad
ManufacturerOrganizer #ad
Part Number10536

6. HiLetgo

#ad

HiLetgo 2pcs A3967 Stepper Motor Drive Board EasyDriver Stepper Motor Driver for Arduino Raspberry Pi Robot

#ad
HiLetgo #ad - The easydriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse or 0 to 3. 3v pulse if you solder SJ2 closed on the EasyDriver. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control. The easydriver has an on board voltage regulator for the digital interface that can be set to 5V or 3. 3v. I. E. Easydriver requires a 7v to 30V supply to power the motor and can power any voltage of stepper motor. Easydriver drives bi-polar motors, and motors wired as bi-polar. 4, 6, or 8 wire stepper motors.
BrandHiLetgo #ad
ManufacturerHiLetgo #ad
Part Number3-01-0831
Model3-01-0831

7. Generic

#ad

Smart Car Robot, 2Pack L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper fit Arduino Electric Projects

#ad
Generic #ad - Large capacity filter capacitance, afterflow protection diode, more stable and reliable. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel h-bridge driver working mode creates higher working efficiency, L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
BrandGeneric #ad
ManufacturerDoes Not Apply #ad
Part NumberNA
ModelNA

8. LAFVIN

#ad

LAFVIN 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

#ad
LAFVIN #ad - Package content: 5 set 28byj-48 stepper motor + Uln2003 Driver Board +20pcs female to male Dupont cable as a gift. Drive module board sizein: 1. 37*1. 18*06 ; stepper Motor diameter: 1. 06in ; stepper Motor lines: 9. 45in. A, c, b, d four-phase led indicates the status of the stepper motor work. Stepper motor with a standard interface. 5 line 4 phase can be used for ordinary uln2003 chip driver, connect to the 2 phase, support the development board,With convenient use, direct docking.
BrandLAFVIN #ad
ManufacturerLAFVIN #ad
Part NumberLA-003
Model903583

9. KeeYees

#ad

KeeYees L298N Motor Drive Controller Board Stepper Motor Control Module Dual H-Bridge with DC Motor and Smart Car Wheel Compatible with Arduino

#ad
KeeYees #ad - It has the strong driving ability, low calorific value and strong anti-interference ability. Tt motor: the motor is a two-axis motor with a reduction ratio of 1:48, which has strong anti-interference ability.

It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project. This is a good parts kit for an arduino and raspberry pi based RC car project. Motor drive controller: l298n used as the main driver chip. Smart car wheels: the wheels are made of high-strength plastic and the tires are made of durable black rubber. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage.
BrandKeeYees #ad
ManufacturerKeeYees #ad